German Shepherd walking in the Bad Pets Enforcer tactical harness

How to Size a Harness for a Big Dog (Without Guessing)

A harness that doesn’t fit isn’t safe, no matter how well it’s built. Too loose and a strong dog can back straight out of it. Too tight and it rubs, restricts the shoulders, and your dog will fight it every walk.

The good news: getting the size right takes two minutes and a soft tape measure. Here’s how to do it properly for a big dog.

What you need

A soft sewing tape measure. If you don’t have one, use a piece of string or a phone charger cable, mark it, then lay it against a ruler or a builder’s tape.

A treat or two helps. Most dogs will stand still for a measure if there’s something in it for them.

Step 1: Measure the chest (the one that matters most)

Run the tape around the widest part of your dog’s chest, just behind the front legs. That’s usually about a hand’s width behind the armpits.

Keep the tape snug but not tight. You should be able to slide two fingers flat under it.

Write the number down. This is the measurement that decides the size.

Step 2: Measure the neck

Run the tape around the base of the neck, where a collar would sit low, not up near the ears. Again, two fingers under the tape.

The neck matters less than the chest, but it tells you whether the top strap will sit comfortably.

Step 3: Check against the size chart

Every harness is cut differently, so always use the chart for the harness you’re buying, not a general “large dog” guide.

For our Tactical Dog Harness – The Enforcer:

Large: chest 71–91 cm, neck 47–79 cm
Extra Large: chest 80–104 cm, neck 54–88 cm

For our One Clip Harness:

Small: chest 60–75 cm, dogs about 17.5–30 kg
Large: chest 70–114 cm, dogs about 30–40 kg

Measurements can vary by 1–3 cm depending on how you measure, so treat the chart as a guide and go by the chest first.

If your dog is between sizes

This is where most people get stuck. A few rules of thumb:

Still growing? Go up. A big-breed puppy can add a lot of chest in a few months, and a harness that fits snugly at the bottom of its range has room to adjust out.

Fully grown and lean? Go with the size where your dog’s chest sits in the middle of the range, not right at the top or bottom. That leaves room to adjust both ways.

Deep chest, narrow waist (think Dobermans, Greyhound crosses)? Go by the chest and tighten the belly strap. Never size up to fit the chest and then leave the rest loose.

Thick winter coat? Measure with the coat, as it is now. If they’re clipped for summer, re-check the straps.

Check the fit once it’s on

The measuring gets you close. The fit check gets it right. With the harness on and adjusted:

Two-finger test. You should fit two fingers flat under every strap. More than that is too loose; less is too tight.

Shoulders free. Watch your dog walk. The front legs should swing freely without the harness sitting on the point of the shoulder.

No rubbing behind the legs. Check the armpits after the first few walks. Redness means a strap is sitting too far back or too tight.

The backing-out test. Hold the lead and gently encourage your dog to back up. If the harness starts sliding over the head, tighten the straps. This is the one that matters on the day a cat crosses the road.

Stays centred. After a walk, the harness should still be sitting straight. If it keeps slipping to one side, it’s either the wrong size or one strap needs adjusting.

Still not sure? Ask us

We’re a small business in Urunga, NSW, and we’d rather help you get the size right the first time. Email info@badpets.net.au with your dog’s chest and neck measurements, breed and weight, and we’ll tell you straight which size to get.

Once you’ve got the fit sorted, you can add your dog’s name with custom velcro patches.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *